Very smart guys)) It's not the first time I've turned to them with keys. And on the sprinter, and on the laguna key card, and on the Skoda rapid. Everything is always at the highest level!! And as for me, everything is normal at their prices, +-ruble as everywhere in the city, so your time is more expensive... as for me, it's a very smart workshop, the guys know a lot and know what they're doing and they've never messed up with me, even though I've contacted them 10 times, that's for sure, because I often stop by om for work...
I'm in shock and not in the best way. I brought the car key to replace the battery. It took the "specialist" 20 minutes to change the battery. A week later, the key "died", I brought it and thought that it was in the battery again, they changed it for me, but literally in a minute. It turned out that the key stopped working completely and what a coincidence that it happened after a 20-minute battery replacement.
I have always been taught to think well of people, and I try to write this review from these positions.
It took two different keys to be made. One is for the KALE lock (double-sided flat), and the other is semicircular (as in the good old button locks).
I decided to choose the place where the keys were made. I took a quick look at the Internet, and there the prices went up... But at one of the points "kluchnik.by" prices are lower per ruble.
You know, there's a ruble, here and there another = and in total = savings.
I came to the construction store "Oma", which is not so close, almost near the MKAD – Napoleon Orda St., 6. I knock on the kiosk for the manufacture of locks kluchnik.by .
They take an order and do it without any problems.
I ask about the cost, and they tell me everything is more expensive per ruble relative to what attracted me on the site. An attempt at a dispute led to the fact that the master offered to make it even more expensive, and they updated the prices of the site 3 years ago ...
I already like the service!
I did, I paid off, took the duplicates and took the check.
I came home, drove the semicircular key into the lock, but it was not there – it does not open. Attempts both this way and that – to no avail. I took the original and everything there immediately "clicked". Try again, but it doesn't ...
The second key from the KALE lock opens without any problems/closes it.
I shot the video and went back to the fabrication shop. Briefly explained that it was not suitable. The master looked at his work, says: "I don't see the difference! I made another one."
I'm already closely checking all the angles, all the distances, okay, I went to test again.
Nothing again! From the twentieth to the thirtieth attempt, I hooked it once and nothing else ...
I again made the third visit to the workshop (! it was the second hour of manufacture!)
The master was again confused, he had already made twenty keys for today, and then some kind of joint ...
I never heard an apology, so I took the money. The only thing that the master admitted is that our equipment does not allow us to hold this key well, it is shortened, so we have to do some of it "by eye".
Of course, I'm already crushing my inner snake, but still the question is ripe: "and where can the most difficult semicircular key be made?"
Everything is fine. 20 minutes and a dozen keys of different formats were ready. Everyone came up, the magnets are working. The price is normal. They work every day.
I don't understand why you should advertise if a person was not in place on three different days, at three different times. And he does not answer calls, and then turns off the phone altogether (and this is during working hours, according to his work schedule)
High-quality repair and manufacture of any keys, of any complexity. The master does everything quickly, which is good news. I replaced the battery in the car key, the battery in the watch in a short period of time. Prices are below the average in the city, the quality is excellent. In the future, I will contact the workshop for the manufacture of keys, a rich selection of blanks, fast and high-quality production, the ability of the master to communicate with customers, which is not a little important!